Chimney Repair in Lexington, KY | Lexington Chimney Cleaning

Chimney Repair in Lexington - You See the Footage Before You Get a Price

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Masonry repairMasonry repair
Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for Lexington Homeowners

Most chimney problems in Lexington announce themselves quietly – a stain on the ceiling after a heavy rain, a puff of smoke that rolls back into the room, mortar that crumbles when you brush against it. Our job is to find what’s actually causing it and fix it before it turns into a rebuild. We’re chimney-only specialists, which means every technician on the job works on flues, crowns, caps, and liners and nothing else. Our technicians have up to 12 years of experience, we’re Insured & Bonded, and every repair starts with a camera inspection so you see the evidence before you approve anything. Call (833) 946-8918 – we answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Same-day repair is often possible in Lexington.

Call (833) 946-8918

Chimney Cap Installation

Chimney Cap Installation is the fitting of a metal or stainless cap on top of the flue to keep rain, birds, and debris out while letting smoke escape. You need one when a flue has no cap at all – common on older Lexington homes where a mortar crown is open to the sky – or when you’re finding nesting material during a sweep. We size the cap to the actual flue opening, which matters more than most homeowners realize: an undersized cap chokes draft and sends smoke back into the living room. We work with Famco and Copperfield caps because the sizing charts and screens are consistent and hold up to freeze-thaw cycles. A typical chimney cap installation in Lexington runs $200-$550 depending on flue count, cap style, and height. The written estimate sets the final price.

Single-Flue vs. Multi-Flue Caps

A single-flue cap bolts down over one opening and suits most wood-burning fireplaces. Multi-flue caps span the whole crown and enclose several flues under one screened housing, which is the better match when your Lexington home has a fireplace plus a furnace flue side by side. We measure every opening before ordering.

Screen Gauge and Animal Guards

Squirrels, starlings, and chimney swifts will find an open flue within a season. A tighter mesh screen stops them and still passes smoke cleanly. We check the screen gauge against your flue size rather than fitting the same box-store cap on everything.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is pulling a rusted, bent, or storm-damaged cap and fitting a new one that actually seals the flue top. It’s time when the old cap has rusted through, lost a leg to wind, or the screen has torn open wide enough for a bird to walk through. A damaged cap stops doing its job, and water then runs straight down the inside of the flue, which is the usual starting point for a cracked crown and spalled brick. We remove the old cap, inspect the crown and flue tile underneath, and set the new unit so it sits level. We use Copperfield and Famco caps because the mounting hardware is stainless and doesn’t rust out in two years like the thin galvanized versions. A typical chimney cap replacement in Lexington runs $180-$450 depending on whether the old cap has to be cut free and how high the stack is. The estimate is free and the written price is final.

Rotted Legs and Fasteners

When a cap’s legs rust out, the whole unit can lift or tilt in a windstorm and leave the flue wide open. We inspect the anchor points and the flue tile rim at the same time. Replacing fasteners before they fail costs far less than replacing the cap screen that follows.

Top-Sealing Dampers

A top-sealing damper combines a cap with an airtight seal that closes when the fireplace is idle, which keeps heat from leaking up the flue. It’s worth asking about during a cap replacement, especially on a Lexington home with a gas fireplace that’s used occasionally rather than daily.

Chimney Liner Installation

Chimney Liner Installation is putting a modern liner inside the flue to create a continuous, properly sized path for exhaust gases. You need it when the original clay tile liner is cracked, broken, spalling from years of heat, or missing altogether inside an unlined chimney – or when a new stove or insert needs a liner sized to its own flue collar. A cracked tile liner lets heat, carbon monoxide, and moisture reach the brick and nearby framing, so this is the one repair we never suggest putting off. We install DuraFlex stainless liner systems and use HeatShield for resurfacing where the existing flue can be repaired rather than relined. Both are professional-grade products installed by trained applicators. Chimney liner installation in Lexington typically runs $2,200-$6,500 depending on height, flue diameter, insulation, and whether the existing tile must be removed. The written estimate sets the final price.

Relining vs. Resurfacing

When the clay tiles are sound but the joints and cracks are the problem, HeatShield resurfacing can restore the flue from the inside without a full tear-out. When tiles are collapsed or the flue is badly oversized for the appliance, a DuraFlex stainless liner is the correct answer. We show you the camera footage and explain which applies.

Sizing to the Appliance

A liner that’s too large cools exhaust before it clears the top, which causes creosote buildup and poor draft. Too small and the appliance won’t draw. We size to the firebox opening, the appliance collar, and the flue height together – not just the pipe diameter.

Chimney Flashing Repair

Chimney Flashing Repair is fixing the metal and sealant where the chimney meets the roof, the joint that leaks most often on Lexington homes. Flashing is the L-shaped metal that sheds water around the chimney base, and when it pulls loose, rusts, or gets sealed with nothing but tar, water finds its way into the attic and ceiling. We reset loose flashing, replace rusted sections, and chase the flashing into the mortar joint so the repair depends on the masonry and not on a bead of caulk that fails after two winters. Rust streaks running down the chimney sides and water stains near the chimney chase are the usual signs. We also work with Famco and Copperfield components where the existing flashing has to be replaced rather than reset. Chimney flashing repair in Lexington typically runs $350-$850 depending on roof pitch, chimney size, and whether the flashing needs to be fully rebuilt. The written estimate is the final price.

Roof Pitch and Access

A steep roof pitch makes flashing work slower and riskier, and it changes the labor. If your chimney sits on a low-slope roof or a complicated valley, the estimate will reflect that access. We tell you upfront instead of adding it later.

Why Caulk Fails

Smearing sealant over a failed flashing joint works for a season, then the water comes back. The fix is to step the flashing into the mortar and counter-flash it properly. If a previous patch was done with tar, we remove the tar and assess the damage underneath.

Chimney Crown Repair

Chimney Crown Repair is fixing the concrete or mortar cap on top of the chimney that diverts water away from the brick. When it’s cracked, pitted, or pulling away from the flue tile, water runs into the chimney walls and the damage spreads down through the masonry. You need crown repair when you see a visible crack across the top, when the crown has crumbled, or when the flue tile stands proud of the crown with no seal around it. We pour or patch the crown with a mix designed to hold up through Kentucky’s freeze-thaw swings, and we form it so water runs off the edge instead of puddling around the flue. Cracked crowns are the most common reason brick spalls on Lexington chimneys. Chimney crown repair in Lexington typically runs $350-$900 depending on crown size, whether it needs to be rebuilt, and whether we’re also repairing a chase cover on a prefab unit. The written estimate sets the final price.

Crowns on Masonry Chimneys

A masonry crown should overhang the brick by an inch or so and slope away from the flue. When it’s flat or does not overlap, water drips down the sides and works into the mortar. We form the repair with that overhang rather than just filling the crack.

Chase Covers on Prefab Units

Prefab fireplaces have a metal chase cover instead of a poured crown, and those rust through. We replace chase covers and check the top of the chase for water entry at the same time. A rusted cover lets rain into the framing around the firebox.

Chimney Repair Companies

Chimney Repair Companies vary widely in Lexington, and the difference usually comes down to whether they do chimney work as their trade or as a side job. A roofer or a general handyman can patch a flashing joint, but repairs inside the flue, crown rebuilds, and liner work demand the right tools and specific training – camera inspection, HeatShield applicator certification, and liner sizing skills. That’s why choosing a chimney-only company matters. When a repair is priced as a lump sum with no camera inspection behind it, or a general contractor tells you the whole flue needs replacing on a walk-through, ask to see the evidence. An honest chimney company will show it and say plainly when work can safely wait. Our chimney repair in Lexington is priced per job from a written estimate, and estimates are always free. We can also work with your insurer on storm-related damage.

What to Ask Before You Book

Ask whether the company is chimney-only or a general contractor, whether the inspection includes camera footage you get to see, and whether the estimate spells out the repair plan in writing. Ask what happens if the sweep turns up a problem mid-job, and whether the price is set before work begins.

Why Single-Trade Focus Matters

Chimney work lives in the details – mortar mixes that hold through freeze-thaw, liner sizing, proper crown slope, correct flashing detail. A team that does only chimneys gets those right because they see the failure patterns repeatedly. We do nothing else.

Chimney Masonry Repair

Chimney Masonry Repair is the work that restores the brick and mortar of the chimney itself – repointing crumbling joints, replacing spalled brick, and rebuilding sections that have lost their bond. You need it when the mortar joints are receding, when brick faces are flaking or falling off, or when a section near the top has begun to lean or crack. Water is the usual culprit in Lexington: it gets behind the brick, freezes, expands, and pops the face off. We grind out failed joints to a proper depth rather than smearing mortar over them, use mortar matched to the older, softer brick common on Lexington homes, and replace damaged units with compatible brick. Chimney masonry repair in Lexington typically runs $600-$3,500 depending on the area involved and whether a rebuild is needed above the roofline. The written estimate sets the final price, and we’ll tell you honestly if a section can wait a season.

Repointing vs. Rebuilding

Repointing – grinding out old mortar and refilling it – makes sense when the brick is still sound and only the joints have gone. A rebuild is needed when the brick itself is spalled or the bond under the crown has failed. We show you which and why.

Freeze-Thaw Damage at the Top

The top of a chimney takes the most weather, so it deteriorates first. A section rebuild up top, with a properly sloped crown above it, protects the rest of the stack from further water intrusion. This is where we focus when the damage is at the roofline.

Brands We Service

We work with professional chimney trade brands because the components inside a flue matter more than homeowners can see from the roof. Our technicians know where each line wears out and how to select the right part rather than the closest box-store substitute. We work with DuraFlex stainless liner systems and understand where they kink, where insulation matters, and how to size them to the appliance. We use HeatShield for liner resurfacing and know when the flue can be restored rather than relined. These are the materials a certified chimney specialist reaches for on a repair, not generic hardware.

We also work with Gelco, Olympia Chimney, Famco, and Copperfield for caps, dampers, and venting components. Familiarity with Famco and Copperfield means proper cap and venting selection rather than guesswork, which protects long-term fireplace performance. Whether you have Famco, Copperfield, DuraFlex, or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Signs You Need a Pro Right Now

  • Water stains on the ceiling or chimney chase. Water entry almost always traces back to a failed cap, flashing, or crown. Every rain a homeowner waits makes the repair a little larger, and once water reaches the framing it can wait no longer.
  • Smoke rolling back into the room. A blocked or undersized flue, a failed damper, or a flue that’s too short all cause backdraft. It’s not just uncomfortable, it’s a sign the flue isn’t moving exhaust the way it should.
  • Crumbling mortar or spalling brick. If mortar joints are receding or brick faces are flaking off, the chimney is losing its structural bond. Repointing early is a smaller job than rebuilding later.
  • Visible cracks in the crown or flue tile. Both let water and exhaust reach places they shouldn’t. A camera inspection shows how far the damage actually goes before anyone quotes a repair.
  • A damaged or missing cap. An open flue invites birds, rain, and debris, and can lead to a blocked flue without anyone noticing. A blocked flue is a carbon monoxide risk, so this one is worth handling before the next burn season.

Our Process, Step by Step

  1. 1
    Call and book. Call (833) 946-8918 and tell us what you’re seeing – water stains, poor draft, visible damage from the yard. We answer 24/7 and book you into the next opening, with fast dispatch from 7am to 7pm, Sunday through Friday.
  2. 2
    Camera inspection. We run a camera down the flue and take still images of every joint, the crown, and the flashing. You see what we see, and the photos are yours to keep.
  3. 3
    Written estimate. We lay out what needs to be done, what can wait, and the price. The written estimate sets the final cost before any work begins. Nothing is recommended without camera evidence you’ve reviewed.
  4. 4
    The repair. We carry the professional-grade materials the job needs – DuraFlex liners, HeatShield resurfacing, Famco or Copperfield caps, and masonry materials matched to your brick. If we find an unexpected issue mid-job, we stop and show you before going further.
  5. 5
    Final check and hand-off. We re-inspect the finished repair with the camera and confirm the flue draws correctly. We leave you the before-and-after photos and a plain explanation of what was done and what to watch for.

How Much Does Chimney Repair Cost in Lexington?

Chimney repair in Lexington typically runs from a few hundred dollars for a cap or flashing fix up to several thousand for a full liner or masonry rebuild. The price depends on which part of the system failed, how far the damage has spread, and how much access the repair requires. A typical cap replacement runs $180-$450, flashing repair $350-$850, and crown repair $350-$900. Liner installation is a bigger job because it addresses the inside of the flue: $2,200-$6,500 depending on height, diameter, insulation, and whether existing tile must come out. Masonry repair lands between $600 and $3,500 based on area. What affects the price most is the extent of the damage – a small crown crack is a far smaller job than a rebuilt chimney top – followed by roof pitch and access, the number of flues, and whether the repair is a resurfacing or a full replacement.

To avoid overpaying, ask to see the camera footage and get the repair plan in writing before anyone starts. If a quote comes in as a lump sum with no inspection behind it, walk away. Our free estimates include the camera inspection, the photo report, the line-by-line pricing, and a plain statement of what can safely wait. Nothing is recommended without evidence you can see. For chimney repair in Nicholasville and nearby areas, we apply the same process. When it comes to whether to reline or resurface, that decision is made from the footage, not from a sales call.

Our Service Area Near Lexington

We work across the Bluegrass region and the surrounding counties. Alongside Lexington, our crews cover chimney repair in Nicholasville, Versailles, Winchester, Paris, Georgetown, Wilmore, Richmond, Lawrenceburg, and Frankfort. The Kentucky climate here is the same everywhere in the region – wet winters with plenty of freeze-thaw cycles that punish mortar and brick – so the repair approach stays the same. Book a sweep or inspection through our Lexington Chimney Cleaning main service, and we’ll schedule the repair for your first available opening. Reach us at (833) 946-8918 to book.

Serving Lexington, KY – Our Local Coverage Area

We serve Lexington and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in Lexington

Schedule Your Chimney Repair Service in Lexington Today

If something about your chimney doesn’t look or smell right, the fastest way to know for sure is a camera inspection and a written estimate – both free. Call (833) 946-8918. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. No obligation, and nothing is recommended without evidence you can see.

Written by the team at Lexington Chimney Cleaning.

Why Lexington Chooses Lexington Chimney Cleaning

We set the standard for chimney repair in Lexington.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Lexington

Getting your chimney repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your chimney repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

We Book a Time That Works for You

A background-checked, certified technician arrives at the time we agree on.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Lexington Customers Say

Trusted by homeowners across Lexington and surrounding areas.

★★★★★

"Drop cloths everywhere, HEPA vac, and not a speck of soot on the carpet. I'd been dreading the mess for nothing."

Wade Sutton
★★★★★

"Liner was cracked in two places. He walked me through the repair options honestly, including the one that was cheaper for him and better for me."

Katie Whitaker
★★★★★

"Work is good and the price was fair. The scheduling was a little loose, the window they gave me was pretty wide and he showed up at the back end of it. Once he was here he was quick and knew what he was doing."

Dale Schaefer

Ready for Chimney Repair in Lexington?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in Lexington.

(833) 946-8918

Request a Free Estimate in Lexington

Tell us about your chimney repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Local Service Coverage
Call Now - We Answer 24/7